input parameter conditions min. typ. max. units input voltage range universal 85 264 vac 110 373 vdc input frequency 47 63 hz input filter meets en 55022 class b; fcc class b input current see model selection guide inrush current cold start, 115 vac 30.0 a pk cold start, 230 vac 60.0 power factor correction meets en 61000-3-2/3 class a leakage current 0.25 ma no load power consumption 0.5 w output parameter conditions min. typ. max. units output voltage/current see model selection guide output voltage tolerance see note 1 ?.0 % line regulation see note 2 ?.0 % load regulation see note 3 ?.0 % ripple & noise (20 mhz) see note 4 ?.0 % hold-up time 230 vac 40 msec temperature coef cient ?.05 %/? over voltage protection 140 % short circuit protection continuous (autorecovery) general parameter conditions min. typ. max. units isolation voltage input to output 3,000 vac isolation resistance 500 vdc 100 m isolation capacitance 2,200 pf emi characteristics parameter standard min. typ. max. units radiated emissions, see note 5 en 55022 class b conducted emissions , see note 5 en 55022 class b esd en 61000-4-2 criteria a; ? kv air/? kv contact rs en 61000-4-3 criteria a; 10v/m eft en 61000-4-4 criteria a; ? kv line & pe surge en 61000-4-5 criteria a; l-n: ?kv, l/n-pe: ?kv cs en 61000-4-6 criteria a; 10 vrms pfmf en 61000-4-8 criteria a; 10 vrms voltage dips, see note 6 en 61000-4-11 criteria a; volt. dips >95%, 0.5 cycle criteria a; volt. dips 30%, 25 cycles criteria a/b; volt. dips 60%, 5 cycles criteria c; volt. inter, >95%, 250 cycles switching frequency fixed 65 khz environmental parameter conditions min. typ. max. units operating temperature range ambient -20 +25 +70 ? storage temperature range -40 +85 ? cooling free air convection (see derating curve) humidity rh, non-condensing 95 % physical size 4.00 x 2.00 x 1.35 inches (101.60 x 50.08 x 34.2 mm) weight 6.34 oz (0.180 kg) reliability speci cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25?, gnd benign 400 khours safety standards ul 60950, en 60950 single output, 100w green, open frame ac/dc power supplies key features: 100w output power 115w with only 7 cfm universal 85-264 ac input en 60950 approved (ul) meets erp directive compact 2 x 4 inch size pfc meets en 61000-3 optional +5v sb output >400 khour mtbf mpg-100s series electrical speci cations speci cations typical @ +25?, nominal input voltage & rated output current, unless otherwise noted. speci cations subject to change without notice. www.micropowerdirect.com micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com
model selection guide mechanical dimensions derating curve notes: 1. output voltage tolerance is measured at 110 vac input and 60% load. 2. line regulation is measured at a 115 vac input with the rated load. the line is varied ?0%. 3. load regulation is speci ed for a load change of 60% 40% (of full load). 4. output ripple is measured at 20 mhz bandwidth and rated load using 0.1 f and 10 f capacitors connected in parallel as close to the power supply terminals as possible. 5. to meet the emi limits, the mounting holes must be connected together (by using metal standoffs). 6. the unit meets en 61000-4-11 criteria a for voltage dips of 60% at 100 vac input. at 240 vac input, it meets criteria b. 7. these units will operate at no load without damage. however, they may not meet all speci cations. 8. the optional remote on/off function is active low. contact the factory for details. 9. each unit includes an input fuse (250v/3.15a). since this fuse is not eld replaceable, it is recommended that an external fuse of the same size be used on the input of the power supply for protection. notes: all dimensions are typical in inches (mm) tolerance x.xx = 0.02 ( 0.50) micropower direct we power your success - for less! 292 page street ste d stoughton, ma 02072 tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com www.micropowerdirect.com model number input output max output power (w) ef ciency (%, typ) current (a) no. voltage (vdc) current (a) 115 vac 230 vac rated max. (w/7 cfm) min. convection cooled with 7cfm air flow mpg-100s-12 2.50 1.25 12.0 8.34 9.59 0.00 100 115 90 mpg-100s-12sb 2.50 1.25 1 12.0 8.34 9.59 0.00 100 115 90 2 5.0 0.10 0.10 0.00 mpg-100s-24 2.50 1.25 24.0 4.17 4.80 0.00 100 115 90 mpg-100s-24sb 2.50 1.25 1 24.0 4.17 4.80 0.00 100 115 90 2 5.0 0.10 0.10 0.00 mpg-100s-48 2.50 1.25 48.0 2.09 2.40 0.00 100 115 90 mpg-100s-48sb 2.50 1.25 1 48.0 2.09 2.40 0.00 100 115 90 2 5.0 0.10 0.10 0.00 input connector (cn1): molex 09-65-2038 or equivalent (one pin removed) mating housing: molex 09-50-1031 or equivalent pin function 1 ac-neutral 2 removed 3 ac-line safety ground: the mounting holes marked ?se metal standoffs should be connected to the system earth ground via metal spacers or a cable. the input side mounting hole marked ?g provides the safety earth ground for the unit. this connection should be locked to prevent possible loosening. connecting the output side mounting hole improves emi. output connector (cn2): molex 09-65-2048 or equivalent mating housing: molex 09-50-1041 or equivalent pin function 1+v out 2+v out 3-v out 4-v out connector (cn3): molex 5045-03a or equivalent mating housing: molex 5043-03 or equivalent pin function 1 remote on/off 2grnd 3 +5vsb connector cn3 is only installed on ?b?models connections
|
